Recommended Shades

12 inch Tall Drum
11 inch Tall Drum

Metal Finishes

Brushed Nickel

Silk Flex Choice, Switch & Plug Colours

Cream
Silver
Black
Brown

Shade Silks

Over 300 Standard Silk options available
Inner Card Lining options in Cream / Gold / Champagne/ Silver / White

IEC (International Electrotechnical Commission) test certificates available

UL (Underwriters Laboratories) test certificates available for the USA - will incur a surcharge

Below are answers to some of the most frequently asked questions from our worldwide clientele. If your particular question is not answered here, please complete the 'Contact Us' form with the details of your query and we will be delighted to respond

CEILING LIGHTS:
In the case of ceiling lights fitted with an adjustable chain, the height of the ceiling light is taken from the lowest point of the fitting to where the chain starts. An allowance of approximately 180mm or 7” should be added to the height of such ceiling lights to allow for a minimal length of chain and the ceiling rose
All ceiling lights are supplied with approximately 500mm or 20" of chain. If additional chain is required please specify this with your order so that the fitting can be wired with an additional amount of cable. Additional costs may apply
Please note that ceiling lights are NOT supplied with fixing hooks or plates. We strongly advise our customers to engage a qualified electrician to inspect and assess the ceiling construction, who can then supply the required hook or fitting mechanism

WALL LIGHTS:
4” or 5” candle clip or base pendant shades can be used on most wall lights, however we recommend half candle clip shades on wall lights with a projection of less than 75mm or 3”
Swing arm wall light heights are measured from the lowest point of the arm to the middle of the bulb holder, except on the WL90 & 91 where the arm is fully adjustable and the height listed refers to the wall mounted rod
Shades smaller than 8” are not recommended for swing arm wall lights

LAMP SHADES:
Shades can be supplied with all global fittings - BC, ES or finial fitting.
All shades of can be supplied with gimbal or base pendant fittings and shades that are smaller than 8" can also be supplied with a candle clip fitting
Finial fitting shades can be supplied on all US & UK lamps if preferred. Please specify if required at the time of order as saddles for harps and finials will need to be added and additional costs will apply
Pleated shades can be made in customers own fabric. Fabric must be supplied on a roll as creases from folding will render the material unusable
Laminated shades cannot be made in customers own fabric

FLOOR LAMPS:
All adjustable floor lamps in the Classic Collection are adjustable by approximately 300mm or 12" in height
Swing arm and adjustable floor lamps can rotate 360 degrees and back again
Swing arm and adjustable floor lamps are weighted to avoid tipping over
Floor lamps are secured in their delivery boxes with a specially designed base section of packaging. To avoid damage to the floor lamp please remove it from either the side or the base of the box
Old English Brass and Antique Brass (black) are unique patina finishes that do not require polishing, only dry dusting

TABLE LAMPS:
All Bella Figura's table lamps are supplied as standard with ES bulb holders. Table lamps can be supplied with Bayonet (BC), US or any other bulb holders in use throughout the world, but this must be specified at the time of order and additional costs may apply
The height of table lamps is measured from the base to the middle of the bulb holder
All Bella Figura table lamps are supplied with silk flex as standard. Please specify the colour required at the time of order
All Bella Figura table lamps are supplied with 2 metres of flex. Extra flex can be supplied at an additional cost if required
All Bella Figura table lamps are supplied with 13 amp plugs as standard. However 5 Amp and 2 Amp plugs are available at an additional cost if required
Old English Brass and Antique Brass (black) are unique patina finishes that do not require polishing, only dry dusting
Polished brass lamps and components are not lacquered and will from time to time require polishing